From DD-WRT Wiki
- Cara Setting Engenius Eoc 2610 User
- Cara Setting Engenius Eoc 2610 Setup
- Engenius
- Cara Setting Engenius Eoc 2610 Manual
- Cara Setting Engenius Eoc-2610
In order to reset the EnGenius EOC-2610 to its factory settings 1. Find the reset button on the rear panel of the router 2.
How to configure Engenius eoc2611P/EOC1650 as point to point or point to multipoint bridge. C lick here for our price. Point to Point or Point to Multi-Point: Using the EnGenius 2611P/1650 series you can create a wireless link between two buildings or multiple buildings. Untuk tambahan sebelumnya pada engenius eoc-2610 memiliki security yang standar dengan user admin dan password admin juga, maka dari itu untuk lebih aman atur security administration pada management, administration dan atur kami mengganti dengan user dan password ‘citrix1’, klik apply.
SENAO EOC-2610
|
THX to malcolmchng
- Ubiquity Nanostation2 clone with better hardware.
- 600mW Wireless Power.
- 24V PoE.
- SuperG 108Mbps Support.
- Internal dual 10dBi panel.
Since many of you guys (me either) have problems with the antenna settings here are some hints to get the right ones working
[edit]Internal
The setting of the internal antenna are a bit tricky due to the fact that the correct state of the settings is REV dependent.You will have to try if secondary or primary antenne setting works better.
For Revision 1.1.13 this setting is diversity on and TX/RX to secondary.
[edit]External
In some Builds you can set the antenna to secondary in some not. If you can set it to secondary and push the hardware switch to ext. Now the rp-sma plug is active
For Revision 1.1.13 this doesnt work corrently as it continues to use the internal.To over come this you can solder RP-SMA connectors onto the internal plugs.[[Image:[1]]]
1. Download the free web server: (you are free to use any other web server that you are familiar with). http://www.ashleybrown.co.uk/downloads/iws2.exe
Cara Setting Engenius Eoc 2610 User
2. Create a folder C:test
3. Download the special V.25 only DD-WRT image from Senao server and copy DD-WRT_newimage.bin into C:testhttp://www.senao.com/images/www.senao.com_English/DD-WRT_newimage.bin?CATNO0=D&CATNO1=D3&CNT=1This image contains DD-WRT firmware; once loaded no additional porting is required.
4. Configure your PC with IP 192.168.1.11 (you can use any other IP also)
5. Start the web server by executing iws.exe and double click on the icon on your system-tray at the bottom-right corner.
6. Configure the web server with the following configuration; click OK when done.
Public Folder ---------> c:testDefault File ----------> index.htmlPort ------------------> 80
Cara Setting Engenius Eoc 2610 Setup
7. Please test the server http://192.168.1.11/ DD-WRT_newimage.bin; it may take a few seconds before the page is completely loaded by your web-browser.
Engenius
8. Power on EOC-2610 and make sure it is complete booted. You can verify it by accessing its web page UI.
9. Once booted; telnet 192.168.1.1; the username & password are both “admin”
10. Under the console prompt type in the following commands in REDtogether with the address link
IMPORTANT: Please note that never interrupt the last command (cat …) under any circumstance (make sure the power is table and do not touch anything during the 3~10 minutes write process). It will cause incomplete write on the flash and make it unbootable. Do not mis-type anything!
Cara Setting Engenius Eoc 2610 Manual
Enjoy!!
Comments are closed.